> System

The Martin Roland MVp2005U is a 70 watts wireless, portable & rechargeable PA (Public Address) system with built-in DVD player and 2-channel UHF wireless microphones. It is an invaluable tool for teaching, presentation and public speaking. It can be used both indoor, such as conference rooms, meeting rooms or auditoriums, and outdoor for an audience of up to 500 people. For indoor use, use the power cord and simply plug it into a wall outlet; for outdoor use, the system runs on two pieces of 12V/5AH Lead-Acid rechargeable batteries, which can last well over 8 hours of continuous use. This system has a built-in DVD player which supports a variety of formats including DVD, CD, CD-G(Karaoke), CD-R, MP3 and even Kodak Picture CD, five different video outputs are available and they are Standard RCA video, S-output, VGA, YUV high luminance chromatism component output and 3-wire composite output (A.K.A. Pr, Pb, Py output). A fully-featured remote control and two pieces of AA batteries are included. This PA system also has one USB input and one SD/MMC card input, they can be used to connect your MP3 players or other devices to play music, it supports both MP3 and WMA formats. Better yet, this system also comes with a built-in Dual UHF wireless microphone receiver, one channel is designated for a handheld Microphone, the other is for a lapel microphone. The transmission range can be as far as 300 feet. For your convenience, there are two additional audio inputs (standard 1/4") that can be hooked up with either wired or wireless microphones. The speaker system is composed of one 70 watts amplifier, one 8" woofer and one 3 1/2" tweeter for clear, powerful sound. Rugged corner-mounted casters and extendible luggage handle are included, self-assembly required (all you need is a screw driver and it takes about two minutes). It also has a built-in tripod mount.

ProTech Systems FasNSeal FSVPK5 5" Variable Pitch Flashing Kit - Flat to 9/12 (300663) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless

ProTech Systems FasNSeal FSWB3 3" Wall Bracket (300430) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless steel designed for extreme resi

ProTech Systems FasNSeal FSELB4504 4" 45 Degree Elbow (300131) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless steel designed for extre

Hydro Systems HS 3837 BF RH Institutional Series Shower EnclosureHydro Systems' mission continues to be developing quality whirlpool products at reasonable prices. As people across the nation continue to learn the therapeutic benefits of hydrotherapy, Hydro Systems continues to develop new technologies and features to create the ultimate bathing experience.Hydro Systems HS 3837 BF RH Institutional Series Shower Enclosure Features:; Shower with grab bars, rod and seat - Right Hand; Overall Dimensions Installed: 38"W x 37"D x 77" H; Gel Coat Finish; Flame spread rating of 200 or less; Smoke density rating of 450 or less per ASTM E84; Galvanized steel reinforced stiffeners; Extra reinforcing in all critical areas; Slip resistant floor; Soap dish; 16" x 30" Satin finish stainless steel grab bar horizontally mounted; Choice of Naughahyde over foam rubber or a hard phenolic folding ; wheelchair transfer seat, factory installed; 36" Satin finish stainless steel curtain rod, installed; Drain is brass body, self-caulking with stainless steel strainer; Unit is packaged in cardboard box on forklift pallet; Full LTL wooden shipping crate available as an option; Hydro Systems producers are backed by our exclusive 5 year limited warranty. Hydro Systems HS 3837 BF RH Institutional Series Shower Enclosure Specifications:; Hydro Systems HS 3837 BF [1;" threshold] shower with 5 year limited warranty, 38" Wide x 37" Deep x 77" High with folding wheelchair transfer seat conforming to ADA accessibility standards, 1" O.D. satin finish stainless steel curtain rod, 16" x 30" satin finish stainless steel grab bar on wet wall and rear wall, one soap dish on wet wall, center drain with center sloping integrally molded slip-resistant floor.; Units shall be molded of gel-coated fiberglass reinforced polyester resin.; Units shall meet or exceed physical and performance requirement for Type 2 gel-coated fixtures [of ANSI Z124.2 showers].; Standing/walking surfaces shall meet slip-res

Compact systems for laboratories requiring <15L of pure water per day. Use feedwater pretreated by reverse osmosis, distillation, or deionization. Microprocessor- controlled purity monitor provides digital resistivity readings, temperature compensated to 25 degrees C (77 degrees F). In standby mode, water recirculates for 10 minutes every hour to maintain purity. A 0.2um filter removes particles and bacteria at outlet. Batch feed models are portable and feature a 7L polypropylene, filtered storage reservoir; low water pump protection; and a 0.5L/min. flow rate. Line feed models are fed from a pressurized feed line or a gravity feed storage tank and have up to 1.5L/min. flow rate. All models produce Type I water with total organic carbon (TOC) content less than 10ppb. UV models feature dual wavelength ultraviolet light (185 and 254nm) to provide water purity of below 3ppb total organic carbon and up to 18.2 megohm-cm. UF models use a 10,000 molecular weight ultrafilter to provide less than 0.001EU/mL pyrogen levels and greater than 4 log reduction of pyrogens. All models have cabinet with metal back and molded plastic front and can be bench mounted. Dimensions: 31.1Wx47.6Dx46Hcm (121/4x183/4x181/ 8"). Electrical: 120/240V, 46/63Hz. Ordering Information: Batch feed models require two cartridges; line feed models require three cartridges. Cartridges are ordered separately. Ultra Low Organics cartridge kits contain three cartridges for use with UV models: Ultrapure, ORGANICFree, and either Pretreatment Deionized Feed (47751-068) or Pretreatment Distilled or Reverse Osmosis Feed (47751-070). Cartridge kits do not include a final filter. VWR offers validation services including IQ, OQ, and PQ protocol development and execution (in US only);

Centerline aluminum systems are designed to provide the bowstring tight net tension insisted on by top programs. The precision machined 26:1 worm gear winch and 2” tensioning strap eliminate backlash found with inferior winch systems. The fold-away tensioning handle is safe, convenient and never gets lost. Totally hidden steel side dowels and bottom net rope and tensioned with Bison’s specially designed rope ratchet tensioners that are easy to tighten and release.Net height adjustment is made precise and quick with our unique Auto Track spring assisted telescoping piston design. Just glide the inner tube up or down and turn knob to lock in place. Centerline systems are infinitely height variable from 72” to 96” and have easy-to-read height adjustment scales. These 3” standards and winch are covered by a lifetime limited warranty.Each complete system comes with 3” floor sockets and brass hinged floor plates, but will fit any existing 3” or larger floor sockets with adapters available upon request at no extra charge. Call for assistance if your existing sockets are more than 12” deep. The 1-1/2” thick, 72” high safety padding exceeds all NCAA, National High School Federation and USVBA rules. Each complete system comes with a set of white cable covers and premium international style antennas. Order VB73 padded official’s stand separately.Pads available in 16 stock colors: Royal, Scarlet, Navy, Forest, Black, Maroon, Gold, Purple, Orange, Kelly, Columbia Blue, Gray, Vegas Gold, Cardinal, Brown and Burnt Orange. Custom screen printing also available.

This system allows the researcher to confirm and track key electroporation parameters, including waveform, peak voltage, field strength, pulse length, pulse duration, and frequency in all electroporation generators with external pulse capabilities. These parameters are critical during optimization sample runs or troubleshooting. The system interfaces between the generator and the electroporation chamber, safety stand or plate handler. System consists of a high-voltage probe and a high-voltage interface box. The probe features an 88.9cm (35") long BNC cable and 30.5cm (12") input leads, and requires four AA cell batteries or connection to an AC adapter for power. The interface box features a 4mm (5/32") banana jack probe connection. The optional communications module allows the user to send the waveform information directly to a printer or a computer. The optional digital storage oscilloscope is required to display waveforms. Probe Specifications Attenuation: 1:100/1:1000 Bandwidth: DC to 70MHz (-3dB) Accuracy: +-2% Input Voltage, Differential Range: +-700V (DC+Peak AC) or 700Vrms @ 1/100, +-7000V (DC+Peak AC) or 5000Vrms @ 1/1000 Common Mode Range: +-7000V (DC+Peak AC) or 2500Vrms @ 1/100 & 1/1000 Output Voltage, Max. Amplitude: +-7V (into 50k ohm load) Offset (typical): <+-5mV Ambient Operating Temperature: -10 to 40 degrees C (14 to 104 degrees ) Ambient Operating Humidity: 25-85% RH Weight: 0.5 kg (1 lb.) Dimensions: 20.3L x 8.3W x 3.8H cm (8 x 31/4 x 11/2") Interface Box Specifications Voltage: 2500Vrms, 3500Vpk CAT II Current (Max. Continuous): 15A Current (Peak): 1000A for 100us Dimensions: 13.5L x 13.5W x 5.8H cm (55/16 x 55/16 x 25/16")

ProTech Systems FasNSeal FSVPK4 4" Variable Pitch Flashing Kit - Flat to 9/12 (300662) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless

ProTech Systems FasNSeal FST3 3" Tee (300175) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless steel designed for extreme resistance to chloride i

OPTIMUM Standard ES1500i (perfect for Home): SPECS: UNIT: 12" X 8.5" X 4.5". Simple, 'plug & play', light, compact, durable unit. Adjust. handle tilts unit for easy reading of display. SEPARATE CONTROLS: Separate timer/current controls w digital display for 1 person. VOLT/WATTS: Input: 100240 vac, Output: 2.522.5 vdc 60 watts, max, works anywhere in world, (Adapters separate) AMP/FREQ: 3.00 Amps foldback, Output 10,000hz SAFETY: Power box safety, dual regulator system, over-voltage & current fold-back circuit protection with 2 amp fuse. High quality electrical component system - all components UL Certified w added safety features. Unit automatically shuts off if array removed from water. BRAND DIFFERENTIATION: Most powerful units on market (3.00 AMPS -5.5 AMPS, other units only 2.5 AMPS) We generate a higher ORP & # neg. ions up to 35x higher than other units. Adjustable current control to compensate for diff body types. Other units dont adjust current & amps is only increased (no decrease) by adding salt (cheap way) which client is receiving a straight 24v current, not healthy. We use regulators to control power. Comprehensive protective mechanism, internal/external fuses & double insulated construction guard against water array blowing fuse. Others use technology not as protective for the end user. Our water array w advanced features: advanced surface design to enhance the ionic osmosis process; welded connections for stronger conductivity; 100% copper; disposable w no cumbersome manual replacement of rings. Others use: copper w Beryllium, can blow fuse w no over flow protection, no welded construction, & require manual replacement of parts. Our technologically advanced components: internal stages of regulation, output, & use of double insulation. Other brands use outdated TR power supply technology, which can malfunction, ripple/spikes or static interference. Optional copper tub to enhance conductivity.

ProTech Systems FasNSeal FSTC4 4" Tee Cap (300206) FasNSeal; is a Special Gas Vent and Gas Vent Connector, made from AL29-4C; stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in Canada Type BH Gas Vent Systems having a rated operating temperature of 480 degrees F and maximum positive pressure of 6" water column. FasNSeal; provides horizontal or vertical venting for high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters. FasNSeal; may also be used as a vent for Category I, natural gas or propane-fired heaters. FasNSeal; must be sized according to the heating appliance manufacturer's instructions, NFPA 211, NFPA 54 and any other relevant local building codes and regulations (see installation instructions for details).Each vent length and component features a built-in mechanical locking band and gasket. Parts are simply pushed together to a stop bead, which renders the joints air and water- tight. By tightening the integrated mechanical locking band, parts are fastened together in seconds. FasNSeal; can be taken apart and reassembled in minutes, making inspection, maintenance or rerouting of FasNSeal; systems a breeze. Should a part or gasket ever become damaged, replacement takes less than five minutes and the integrity of the system is not compromised! Connecting FasNSeal; to a heater is done efficiently with one of our many adaptors approved by heating appliance manufacturers. Heating equipment can be fired up immediately upon completing a FasNSeal; installation, as no cure time or cleanup is required. FasNSeal; features a smooth weld seam inside and out, which is completely shielded during the TIG welding process. Contamination or molecular changes in the weld seam are avoided; no fillers are used in the welding process. FasNSeal; is manufactured from AL29-4C;, a superferritic stainless steel designed for extreme resistan

Voice Alert System-6 is a new annunciator system featuring wireless PIR sensors transmitters and a remote receiver/speaker base unit. You record their own alert messages and are then notified with your own voice message when activity in a monitored area is detected. Key applications include: Wireless Driveway Alarm Residential and Small Business Security Child Monitoring and Pool Safety Home Automation System-6 allows a maximum of six user recorded messages. Each message is specific to one zone. For instance, zone one could be for a driveway alarm -Car coming up the driveway while zone two could be for a sensor monitoring the back yard- Alert! Child by the pool! Perhaps a third sensor guards a side entrance against intruders. However, when this PIR detects movement, the base unit plays Intruder on patio and triggers a floodlight using one of four relays included on the base unit. System-6 can monitor all three zones simultaneously and still have three additional zones available when needed. Users can alter their messages and place the wireless sensors wherever they wish. Voice Alert System-6 sets up in minutes and can be completely customized to fit their individual needs. The wireless PIRs feature: all weather protection, adjustable mounting and sensitivity, and can send a signal 300 feet through walls and up to 1000 feet in open space. These transmitters connect to sensing devices such as smoke alarms, motion and CO detectors, window/gate/door contacts, door bells, water level indicators or pressure pads. When the sensing device is triggered, the transmitter signals the Voice Alert System. The TXPCBB-V also has a vibration sensor that will trigger if the transmitter is bumped or moved. Can be used in conjunction with VA-6000T transmitters.

Uniden Wireless Security System The Uniden Wireless Security System is an easy to use and simple to install surveillance device that utilizes 2.4GHz wireless technology. With a built-in speaker, quad, AutoScan or full screen view, and digital zoom, pan and tilt capabilities, users can feel safe knowing they have a reliable system working around the clock. The included computer software allows users to utilize other special features such as detection sensitivity, playback, smart motion detection and alarm and scheduled recordings onto your computer. Equipped with a rechargeable battery, the Uniden System's camera can operate up to 4 hours and the base can go up to 10 hours before recharging is needed. With two similar systems available, users may purchase the system that best fits their needs knowing that both come fully equipped with the same features. The Uniden Indoor System comes with a smaller display screen monitor and one mountable in-door only camera; the Uniden Outdoor System comes with a slightly larger display screen monitor, two weather-proof mountable outdoor only cameras and a remote control. Both systems provide users with the security and peace of mind that other surveillance devices might not provide; buy the Uniden Wireless Security System today from ActiveForever! Uniden Wireless Security System Features: Portable, wireless and discreet Built-in speaker Color display with night vision Quad, AutoScan or Full Screen view Playback feature Smart motion detection and alarm Scheduled recordings onto a computer Digital zoom, pan, and tilt capability Detection sensitivity Simple plug and play technology Camera can be used on mounted stand, wall, ceiling or built-in stand Uniden Wireless Security System Specifications: Monitor Display Dimensions (Indoor system): 3.5" Monitor Display Dimensions (Outdoor system): 7" Monitor Type: Color display Battery: portable ion rechargeable battery Software: PC software included (XP & Vista compatible) Camera Transmits: up to 500ft. (subject to environmental conditions) Available: either with one (1) indoor camera OR two (2) outdoor cameras Includes: Camera (or cameras, depending on package chosen), monitor, 1 camera stand, 1 camera power adapter, 1 monitor power adapter, 1 USB cable, 1 Uniden Video Surveillance software disk, 1 set AV cables (RCA plugs), owner's manual Warranty: 30 day warranty Returns: All returns subject to ActiveForever's return policy and a 20% reprocessing fee. Please call Customer Service for a RMA (Return Merchandise Authorization) Number. Unauthorized returns will not be accepted. Related Searches: UDW10003, UDW20055, security - Uniden Wireless Security System - W/ 2 Outdoor Cameras UDW20055

Uniden Wireless Security System The Uniden Wireless Security System is an easy to use and simple to install surveillance device that utilizes 2.4GHz wireless technology. With a built-in speaker, quad, AutoScan or full screen view, and digital zoom, pan and tilt capabilities, users can feel safe knowing they have a reliable system working around the clock. The included computer software allows users to utilize other special features such as detection sensitivity, playback, smart motion detection and alarm and scheduled recordings onto your computer. Equipped with a rechargeable battery, the Uniden System's camera can operate up to 4 hours and the base can go up to 10 hours before recharging is needed. With two similar systems available, users may purchase the system that best fits their needs knowing that both come fully equipped with the same features. The Uniden Indoor System comes with a smaller display screen monitor and one mountable in-door only camera; the Uniden Outdoor System comes with a slightly larger display screen monitor, two weather-proof mountable outdoor only cameras and a remote control. Both systems provide users with the security and peace of mind that other surveillance devices might not provide; buy the Uniden Wireless Security System today from ActiveForever! Uniden Wireless Security System Features: Portable, wireless and discreet Built-in speaker Color display with night vision Quad, AutoScan or Full Screen view Playback feature Smart motion detection and alarm Scheduled recordings onto a computer Digital zoom, pan, and tilt capability Detection sensitivity Simple plug and play technology Camera can be used on mounted stand, wall, ceiling or built-in stand Uniden Wireless Security System Specifications: Monitor Display Dimensions (Indoor system): 3.5" Monitor Display Dimensions (Outdoor system): 7" Monitor Type: Color display Battery: portable ion rechargeable battery Software: PC software included (XP & Vista compatible) Camera Transmits: up to 500ft. (subject to environmental conditions) Available: either with one (1) indoor camera OR two (2) outdoor cameras Includes: Camera (or cameras, depending on package chosen), monitor, 1 camera stand, 1 camera power adapter, 1 monitor power adapter, 1 USB cable, 1 Uniden Video Surveillance software disk, 1 set AV cables (RCA plugs), owner's manual Warranty: 30 day warranty Returns: All returns subject to ActiveForever's return policy and a 20% reprocessing fee. Please call Customer Service for a RMA (Return Merchandise Authorization) Number. Unauthorized returns will not be accepted. Related Searches: UDW10003, UDW20055, security - Uniden Wireless Security System - W/ 1 Indoor Camera UDW10003